ReadyMadeRC
8W V6 PRO BOOSTER FOR 433MHZ DIGITAL SYSTEMS
| FEATURES of V5 | added safety and security |
Vin, Current in, RF Power Out, Efficiency:, 9.0V 2.58A 9.12W 39% DO NOT GIVE UNIT OVER 8V, Different cable types have different loss, here is the max length allowed using different cables:, RG-58CU 18meters (59ft), Old 3xx rx firmware:, The ultra sensitive receiver will be blocked/jammed if distance to booster antenna is under 10-20meters so avoid that !, NEW 307-308 or higher RX firmware:, No more blocking problems, an RX can be as close as 25cm (10 inch) from a booster at 7W before minor blocking is detected., WARNING:, Power supply MAX is 8.4V, max supply current 2.5A, newer ever exceed that., Notice: The use and operation of this product in the USA and many other countries requires an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
Here is the NEW PA Booster version 6 PRO, again ...ReadyMadeRC
FATSHARK BASE SD VGA VIDEO GLASSES
| interpupillary (ipd) distance | 59-69mm (adjustable) |
| power input | 7-13v (2s/3s supply) |
| power consumption @12vdc | 100ma |
| weight | 120g |
| option 1 | the |
| Option 3 | Any 2s-3s lipo with a 2.1mm barrell connector like |
package includes:, , specifications:, , Option 2: If you want to share the power supply with your ground station, the included cable allows for that. You simply feed the power from the 2.1mm barrel connector that normally powers your video receiver/ground station into the included cable, and then plug the extra power plug included on the cable into your video receiver/ground station so you are powering both devices with the same battery.,
built for serious fpver’s, the new base sd goggle is ...ReadyMadeRC
10.1 INCH RMRC LCD MONITOR
| Image | 10.1" TFT LCD LED Backlit |
| Resolution | 1024x600 |
| Horizontal frequency range | 30-98KHz |
| Field frequency range | 60-75Hz |
| Brightness | 450cd/m² |
| Viewing Angle | 70°/70°(L/R) 40°/50°U/D |
| Contrast Ratio | 500 |
| Response time | 8ms |
| Input Voltage | DC7-18V |
| Power Consumption | ≦10W |
| Input Signal | VGA,AV1,AV2,Audio,HDMI |
| Working Temperature | -20℃～60℃ |
| Storage Temperature | -30℃～70℃ |
| Size | 255L×163W× 34D mm |
| Weight | 544g without cables or sun shield, 875g with cables and sun shield |
| Mounting | Standard 1/4-20 tripod and VESA mounts |
Specifications:, Display Ratio: 16:9, Package Includes:, 10.1" LCD Monitor,
NOW 450cd/m² brightness! Perfect for your FPV ground station, this ...ReadyMadeRC
BOBCAT 6 CHANNEL 1.14M WINGSPAN PUSHER (PNP)
| Material | EPO |
| Wingspan | 1143mm(45inch) |
| Flying Weight | 1400g（49.5oz） |
| WingArea | 31d㎡(480in2) |
| Wingload | 50g/d㎡(16oz/sq.ft) |
| Drive System | 3648 KV1250 motor |
| Servos Required | 7*9g servos |
| Propeller | 7*6 3 Blade Custom |
| Battery Recomended | 14.8V,2700-3300mAh Li-polymer |
| Control system | Minimum 6 CH |
*Special note from RMRC: This plane flies great, but we have seen some issues with the power system and included hardware, which is why we have discounted the plane. The user should replace the wires between the motor/esc with thicker gauge wire (we recommend 12AWG) and double check the soldering on the bullet connectors, and also should cut open a hole beside the ESC for additional cooling. The best option would be to supply your own 80A ESC based on the results we've seen with the inclulded ESC's Double/triple check all hardware, servo wires, etc. We are pricing this at near the kit price and losing money on these since we are not particularly happy with the included electronics, but once you get it in the air we think you'll be happy with how it flies. We have no idea how other stores can justify charging $300 for the same plane., Some special instructions for this plane:, ,
Bobcat jet-style kit with integrated LED's and retracts included! High ...ReadyMadeRC
DJI WOOKONG MULTI (WK-M) MULTIROTOR CNTRL
| Built-In Functions | Autopilot, Auto Hover Fail Safe |
| Multi Rotor Types | Quad-Rotor, Hex-Rotor, Octo-Rotor |
| Supported ESC output | 200Hz refresh frequencys |
| Recommended Transmitter | PCM or 2.4GHz with minimum 5 channels and Failsafe function available on all channels |
| Recommended Power Supply | DC 4.8 ~ 12V |
| Power Consumption | MAX 5W (0.9A@5V, 0.7A@5.8V,0.5A@7.4V,0.4A@8V) |
| Hovering Accuracy | Vertical |
| Suitable Wind Condition | < 8m/s (17.7mph) |
| Max Rotate Angle | 30° |
| Vertical Speed | 3m/s |
| Total Weight | <= 150g |
| Dimensions | Main Controller |
| IMU | 40mm x 31mm x 26mm |
| GPS & Compass | 50mm (diameter) x 9mm |
| LED Indicator | 25mm x 25mm x 7mm |
Introduction:, , Features:, , Operating Temperature: -5°C to +60°C (You have to keep the IMU warm if you want to use it under low temperature, could be -5°Cor lower.),
DJI Wookong Multi-Rotor stabilization controller is a complete flight system ...ReadyMadeRC
TSLRS TX600+ UHF TRANSMITTER
| Transmitter power 3 steps | 0.5W 1W and 2Watts |
| Watt / SupplyVolt = Current, the supply voltage can be anything from 6-25V. Example with a 3S lipo | 1.5W / 11V = 0.126A |
Example: 1000mAh / 126mA = 7.9 hrs, remember to keep a good safe margin, some batteryes like LIPO do not like to be fully empty., Notice: The use and operation of this product in the USA and many other countries requires an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
Now able to handle any PPM signal input, with no ...ReadyMadeRC
RMRC FPV1000 DVR
| Video format | MPEG4 |
| File Container | AVI |
| Bitrate (high) | 7000Kb/s* |
| Photo format | JPG |
| High Resolution LCD | 2.5", TFT true color LCD |
| Audio and video output | RCA 3-in-1 AV output (for playback of recordings or live pass-through) |
| Storage type | SD card up to 32GB, Class 10 recommended |
| Video Standards | PAL |
| One AV cable includes power supply for external camera or device | Voltage |
| Video format | NTSC/PAL |
| Multi record mode | Manual/Auto |
| Computer Transfer | USB2.0 |
| Recording time | 1minute~2.5 hours /1G |
| Power consumption | 200mA , 3.7V 1000 mAH chargeable Li-ion battery |
| Size | 79 mm x 51 mm x22 mm |
| Weight | 85g (including battery) |
| Excellent choices for SD Cards | 16GB Class 10 |
Package Includes:, DVR, Warranty: 30 day new replacement for factory defects, 1 year replacement with new or refurbished unit for factory defects. Warranty does not cover DVR's that have been damaged by supplying power with an incompatible source, or any other damage caused by user error., Available accessories:, ,
New RMRC FPV1000 DVR This compact, light weight DVR is ...ReadyMadeRC
FY-DOS INERTIAL ATTITUDE STABILIZER WITH GPS
INCLUDES:, , IMPORTANT: The GPS receiver uses 5V, and therefore the DOS system outputs 5V to power the GPS receiver. Feiyu GPS receivers made for other models, and most other GPS receivers, use a lower voltage and will be damaged if you connect them to the DOS., New function:, , The latest firmware for Multi-rotor flight system is V2.0 can realize the following functions:, , For more detail:, FY-DoS for multi-rotors control manual,
DoS is an aeromodelling balancing instrument designed for a variety ...ReadyMadeRC
FY-DOS INERTIAL ATTITUDE STABILIZER
Included in this version:, , IMPORTANT: The GPS receiver uses 5V, and therefore the DOS system outputs 5V to power the GPS receiver. Feiyu GPS receivers made for other models, and most other GPS receivers, use a lower voltage and will be damaged if you connect them to the DOS., New function:, , The latest firmware for Multi-rotor flight system is V2.0 can realize the following functions:, ●, For more detail:, FY-DoS for multi-rotors control manual,
DoS is an aeromodelling balancing instrument designed for a variety ...ReadyMadeRC
PRO700 700TVL WDR CCD (NTSC)
| PAL | (H)1024x(V)596; NTSC |
| S/N Ratio | More Than 50dB (AGC off) |
| DNR | 2D DNR (Digital Noise Reducer) |
| Electronic Shutter | PAL |
| Video Output | 1Vp-p 75 Oms , Negative |
| Audio Output | 300mV at 600 Oms |
| Operating Temperature | -10℃ ~ + 50℃, RH 95% Max |
| Storage Temperature | -20℃ ~ + 60℃, RH 95% Max |
Pixels:, Power Consumption:, DC 5V-15V, 150mA-50mA,
Offering the best picture available for FPV, PERIOD! I challenge ...ReadyMadeRC
PRO700 700TVL WDR CCD (PAL)
| PAL | (H)1024x(V)596; NTSC |
| S/N Ratio | More Than 50dB (AGC off) |
| DNR | 2D DNR (Digital Noise Reducer) |
| Electronic Shutter | PAL |
| Video Output | 1Vp-p 75 Oms , Negative |
| Audio Output | 300mV at 600 Oms |
| Operating Temperature | -10℃ ~ + 50℃, RH 95% Max |
| Storage Temperature | -20℃ ~ + 60℃, RH 95% Max |
Pixels:, Power Consumption:, DC 5V-15V, 150mA-50mA,
Offering the best picture available for FPV, PERIOD! I challenge ...ReadyMadeRC
BOSCAM AIO GOGGLES KIT WITH CAMERA AND 5.8 AND 2.4G TX
| Resolution ratio | VGA 640x480RGB;display pixel |
| Frequency | 8channles 2.4G&5.8GHz |
| Antenna connector | RP-SMA |
| Color | sliver |
| Weight | 490 |
| Level sharpness | 480 TV Line |
| Video format | PAL/NTSC |
| View angle | 90 º |
| The lowest lighting | 1Lux/F1.2 |
| Net weight | 87g |
| Gross weight | 105g |
| Transmitting Power | 200mW/23dBm |
| Transmitting distance | >2000m(open area) |
| Frequency control | built-in frequency and phase lock loop |
| AV input | analog AV signal input |
| ANT connector | RP-SMA(inside the needle) |
| Power supply | 6.5-12 volts |
| Current supply | 200mA |
| Size | 55*26*17mm |
| Net weight | 43g |
| Gross weight | 52g |
| Transmitting Power | 500mW/27dBm |
| Transmitting distance | >4000m(open area) |
| Frequency control | built-in frequency and phase lock loop |
| AV input | analog AV signal input |
| ANT connector | RP-SMA(inside the needle) |
| Power supply | 5-12 volts |
| Current supply | 300mA |
| Size | 55*26*17mm |
| Net weight | 43g |
| Gross weight | 52g |
Includes:, , Manufacturer Specs:, Transmitter frequency:Amateur Radio Band, 5865M, 5845M, 5825M, 5805M, 5785M, 5765M, 5745M, 5725M;8CH;8CH (not frequency-compatible with FatShark, ImmersionRC, or Airwave based equipment), Transmitter frequency:2370-2510MHz; 8CH (Units shipped to US addresses are locked and include channels at 2414MHz and 2432MHz only, no exceptions!), Notes: These use reverse polarity, RP-SMA connectors and may require an adapter with the use of some antennas. Although ImmersionRC A/V connectors fit, the power/ground will need to be reversed before use., Notice: The use and operation of this product in the USA and other countries may require an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
BOSCAM GS920 FPV Goggles Angle of view：32° Virtual photo size：3.5m ...ReadyMadeRC
5 INCH RMRC LCD FPV MONITOR
| Image | 5.0" TFT LCD LED Backlit |
| Resolution | 800x480 |
| Horizontal frequency range | 30-60KHz |
| Field frequency range | 60-75Hz |
| Brightness | 350cd/m² |
| Viewing Angle | 70°/70°(L/R) 50°/70°U/D |
| Contrast Ratio | 500 |
| Response time | 10ms |
| Input Voltage | DC6-24V |
| Power Consumption | ≦7W |
| Input Singal | Video, Audio |
| Working Temperature | -20℃～55℃ |
| Storage Temperature | -30℃～65℃ |
| Size | 146L×100W× 46D (60.5D with sun shade) mm |
| Weight | 260g without cables or sun shield, 340g with cables and sun shield |
| Mounting | Standard 1/4-20 tripod and VESA mounts |
Specifications:, , Display Ratio: 16:9, Package Includes:,
Perfect for your FPV ground station, this Ready Made RC ...ReadyMadeRC
BOSCAM TS351 5.8G 200MW AV TRANSMITTER
| Transmitting Power | 200mW/23dBm |
| Transmitting distance | >2000m(open area) |
| Frequency control | built-in frequency and phase lock loop |
| AV input | analog AV signal input |
| ANT connector | SMA(inside the needle) |
| Power supply | 6.5-12 volts |
| Current supply | 200mA |
| Size | 55*26*17mm |
| Net weight | 43g |
| Gross weight | 52g |
Transmitter frequency: Amateur Radio Band, 5865M, 5845M, 5825M, 5805M, 5785M, 5765M, 5745M, 5725M;8CH Not frequency-compatible with FatShark, ImmersionRC, Airwave based equipment, Notice: The use and operation of this product in the USA and other countries requires an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
5.8G 200mW AV wireless transmitter They do not work with ...ReadyMadeRC
SMARTFPV - 3 WAY RC VIDEO SWITCH BY KRISTAPS
| All pin headers have same pin functions | GND, +V, Video |
Introduction:, SmartFPV 3 way RC video switch allows switching between 3 cameras while flying FPV. You can switch between flight camera, back view camera and camera facing down or use switch to see view from camera that takes pictures., Features:, - 3 video inputs, 1 video output, Connecting:, You can connect RC video switch to RC receiver’s regular servo channel or sum PPM connector. It will automatically detect type of RC signal., Configure PPM control channel:, To change PPM channel used to control video switch you need to toggle 8 times needed transmitter switch within 10s after video switch is powered ON., Video connectors:, SmartFPV video switch has 3 video inputs and 1 video output. Connection is made with common 3 pin servo style connectors., Video power:, All middle pins of 3 pin video connectors are interconnected to share same power between video cameras and video transmitter connected. You can power all devices either by feeding voltage to one of video devices connected or by soldering additional leads to battery input and connect battery. Battery connection leads are not included.,
- Regular servo channel or sum PPM control from RC ...